How to Set up a Bath Tub: Install an Acrylic Tub and Also Tub Surround
How to Set up a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Blog Article
We have noticed this great article relating to Installing A Bathtub directly below on the net and accepted it made good sense to share it with you on my blog.
Mounting a bathtub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a brand-new one is also a moderately difficult project. If the old bathtub is readily accessible, the project can move easily; if you need to open a wall to remove the old tub and also position the brand-new bathtub, the job is a lot harder. In either case, the job is within a home handyman's skills, although you will require a helper to vacate the old bathtub and embeded in the new one. Ensure you have actually qualified on your own for the work as well as are comfortable attempting it. As opposed to hiring a contractor to take control of a halfway-completed job, it is far better to consider utilizing one prior to you start. Chances are you may need a specialist plumber to make tube links.
This short article will certainly help you set up a new bath tub in your bathroom if you have currently purchased a brand-new tub and do not require to alter the plan of your previous water supply pipes.
Your tools and also material list must consist of the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be fairly bothersome due to the restricted gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been eliminated, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
Prior to carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making certain that the washing machines are in location between the tap as well as the sink. Secure the tap in place with the maker supplied backnut. When the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet ports. The former kind should be linked to the faucet ends first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Making use of both wood boards under its feet, place the tub in the called for setting. The wooden boards are useful in uniformly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub up until the level reads level.
To mount faucets, fit the bottom of the furthest flexible tap connector to the proper supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the water supply and examine all joints and brand-new pipework for leakages and also tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet and the regular electrical outlet for leakages.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and also securing around the tub ought to wait up until the bath tub has actually been utilized a minimum of once as this will certainly resolve it into its last placement.
Getting ready for the Setup
First of all, the supporting structure supplied with the bath ought to be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its final setting.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to crack a rigid seal, triggering the water to penetrate the wall surface between the bath and the tiling, bring about complications with moisture and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly load the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in usage. The sealer can break rather early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that report on Installing A Bathtub through an associate on our other website. Sharing is caring. Helping people is fun. I praise you for your time. Visit us again soon.
Source This Article
Report this page